[EXFO ETS-1000L] 이더넷 루프백 장치 / ETHERNET LOOPBACK DEVICE
EXFO ETS-1000L ETHERNET LOOPBACK DEVICE
주요특징 (Features)
• 10/100/1000BaseT and GigE ports
• Can be used as a remote loopback/reflector for all carrier Ethernet validation tests including RFC 2544, bit-error rate (BER) and quality of service (QoS)
• Selectable loopback at layers 1 through 4
• Complete interoperability with EXFO’s Ethernet analyzers (ETS-1000, AXS-200/850 series, RTU-310/310G) and Ethernet test modules (FTB-8510B, FTB-8510G, FTB-8525/8535 and FTB-8120NGE/8130NGE)
• 802.3ah remote loopback support
상세설명 (Description)
Field Assessment of Carrier Ethernet Services
EXFO’s ETS-1000L is a cost-effective, compact Ethernet loopback tool that can be used as a remote unit to return test traffic, enabling service providers to turn-up and install next-generation Carrier Ethernet services. It is fully compatible with EXFO’s complete portfolio of Ethernet analyzers (ETS-1000, AXS-850 series, RTU-310/310G) and Ethernet test modules (FTB-8510B, FTB-8510G, FTB-8525/8535 and FTB-8120NGE/8130NGE).
The ETS-1000L supports the following interfaces: 10/100/1000Base-T, 1000Base-SX, 1000Base-LX and 1000Base-ZX. Thanks to this simple loopback tool, technicians can loop back traffic up to layer 4 with configurable MAC, IP and VLAN parameters. The ETS-1000L can also be used as an endpoint for all of today’s necessary Ethernet/IP field testing applications including RFC 2544, bit-error-rate testing, packet jitter as well as multistream generation and analysis (quality of service testing).
Key Features
• 10/100/1000BaseT and GigE ports
• Can be used as a remote loopback/reflector for all carrier Ethernet validation tests including RFC 2544, bit-error rate and
• quality of service (QoS)
• Supports user-configurable full line rate loopback at layers 1 through 4
• 802.3ah remote loopback support
• Complete interoperability with EXFO’s Ethernet analyzers (ETS-1000, AXS-200/850 series, RTU-310/310G) and Ethernet test modules (FTB-8510B, FTB-8510G, FTB-8525/8535 and FTB-8120NGE/8130NGE)
• Responds to ping requests
• Configurable MAC/IP address and VLAN
Technical specifications (Optical interfaces)
OPTICAL INTERFACES | |||
Available wavelengths (nm) | 1000Base-SX | 1000Base-LX | 1000Base-ZX |
---|---|---|---|
Wavelength (nm) | 850 | 1310 | 1550 |
Transmission level (dBm) | –9 to –3 | –9.5 to –3 | 0 to +5 |
Reception level sensitivity (dBm) | –20 | –22 | –22 |
Maximum reach | 550 m | 10 km | 80 km |
Transmission bit rate (Gbit/s) | 1.25 | 1.25 | 1.25 |
Reception bit rate (Gbit/s) | 1.25 | 1.25 | 1.25 |
Transmission operational wavelength range (nm) | 830 to 860 | 1270 to 1360 | 1540 to 1570 |
Maximum reception before damage (dBm) | +6 | +6 | +6 |
Jitter compliance | IEEE 802.3 | IEEE 802.3 | |
Ethernet classification | IEEE 802.3 | IEEE 802.3 | |
Laser type | VCSEL | FP | DFB |
Eye safety | Class 1 | Class 1 | Class 1 |
Connector | LC | LC | LC |
Transceiver type | SFP | SFP | SFP |
ELECTRICAL INTERFACES | |||
Electrical interfaces | Two ports, 10/100BaseT half/full duplex, 1000BaseT full duplex Straight/crossover cable auto-detection |
||
Transmission bit rate | 10 Mbit/s | 125 Mbit/s | 1 Gbit/s |
Transmission accuracy (ppm) | ±100 | ±100 | ±100 |
Reception bit rate | 10 Mbit/s | 125 Mbit/s | 1 Gbit/s |
Duplex mode | Half and full duplex | Half and full duplex | Full duplex |
Jitter compliance | IEEE 802.3 | IEEE 802.3 | IEEE 802.3 |
Connector | RJ-45 | RJ-45 | RJ-45 |
Maximum reach (m) | 100 | 100 | 100 |
Technical specifications (Ethernet Functional Specifications)
TESTING | |
Loopback | Ability to return traffic to the local unit by swapping packet overhead up to layer 4 of the OSI stack; user-selectable. |
---|---|
802.3ah (OAM) | Supports 802.3ah Ethernet-in-the-First-Mile OAM passive mode, allowing remote test equipment to initiate a loopback on the ETS-1000L. |
Configurable address | Ability to configure the MAC,IP addresses and VLAN ID of the test port. |
Remote control | Remote control of the unit via a test port. |
GENERAL SPECIFICATION | |
Size (H x W x D) | 125 mm x 68 mm x 30 mm |
Weight | 0.135 kg |
Temperature | operating : 0 °C to 45 °C |
storing : –40 °C to 60 °C | |
Relative Humidity | 0 % to 93 %, noncondensing |
Power consumption | 12 W |
Languages | English, Spanish, Chinese |
- 배송비 : 1,000,000원 이상 구매시 무료배송이며, 미만 주문시 5,000원의 택배비가 청구됩니다.
도서, 산간지방 및 일부지역은 배송비가 추가될 수 있습니다.(퀵, 다마스 배송은 별도 문의부탁드립니다)
- 배송기간 : 배송은 일반적으로 결제후 2~7일이 소요됩니다.(토요일/공휴일 제외, 도서지역 4~8일)
특수제품, 주문제작 및 직수입 상품의 경우 별도 배송일을 안내해 드립니다.
배송예절일은 주문시점(주문순서)에 따른 유동성이 발생하므로 평균 배송일과 차이가 발생할 수 있습니다.
- 본 상품의 배송 가능일은 15일입니다. 배송 가능일이란 본 상품을 주문 하신 고객님들께 상품 배송이 가능한 기간을 의미합니다.
(단, 연휴 및 공휴일은 기간 계산시 제외하며 현금 주문일 경우 입금일 기준 입니다.)
교환/환불 |
환불 |
교환 |
단순변심 |
고객님 부담으로 환불금액에서 왕복 배송비가 차감되어 환불됩니다. |
왕복 배송비 확인 후 박스에 동봉해서 보내주세요. - 일반적으로 교환이나 환불시 10,000원의 왕복배송비가 적용됩니다.(상품에 따라 상이 할 수 있습니다) - 재고가 없는 경우 환불처리 될 수 있습니다. |
제품하자 및 오배송 |
판매자 부담이므로 상품만 보내주시면 됩니다. |
교환/환불이 불가능 한 경우 |
|
환불/교환 요청기간 초과 |
환불/교환 기간 이후 요청하는 경우(배송완료 시점으로부터 15일 초과시) 단, 수령한 상품이 표기 광고의 내용과 다르거나 계약 내용과 다르게 이행된 경우에는 수령한 날로부터 3개월 이내, |
재고가 부족한 경우 |
단순변심으로 교환을 요청했으나, 재고가 부족한 경우(환불 처리 될 수 있습니다) |
특수제품/ 주문제작/ 직수입제품 |
주문/제작 상품의 제작이 이미 진행된 경우, 직수입 제품의 경우 주문서가 들어간 경우 |
분실/ 파손/ 고장/ 오염 발생 | 상품택/ 구성품 분실 및 취급 부주의로 인한 파손/고장/오염 등이 발생한 경우 |
모니터 해상도 차이 | 모니터 해상도 차이로 인하여 색상 등 이미지가 실제와 상이한 경우 |
기타 불가사유 | ① 제품박스가 손상되거나 찢어진 경우 ② 고유팩 포장을 분리하거나 훼손하였을 경우 ③ 렌즈에 이물질 및 지문등의 흔적이 남은 경우 |
<기타 불가 사유 참고 이미지>
|
- 상품 택(tag)제거 또는 개봉으로 상품 가치 훼손 시에는 상품수령후 7일 이내라도 교환 및 반품이 불가능합니다.
- 일부 특가 상품의 경우, 인수 후에는 제품 하자나 오배송의 경우를 제외한 고객님의 단순변심에 의한 교환, 반품이 불가능할 수 있사오니, 각 상품의 상품상세정보를 꼭 참조하십시오.
- 상품 청약철회 가능기간은 상품 수령일로 부터 15일이내 입니다.
- 일부 특수 제품, 주문제작 및 직수입 제품의 경우 교환/반품이 어려울 수 있습니다.
- 구매전 충분히 상담하시고, 신중하게 구매 해 주시기 바랍니다.
- 저희 텍캄몰에서 구매하신 제품과 상품은 정품으로 본사 및 전문점에서 A/S를 받을 수 있습니다.
- 무상 A/S기간에 상관없이 밴드교체 및 유리교체 등 소모품성 및 고객님의 부주의로 인한 파손은 유상 A/S(비용청구)로 처리됩니다.
- A/S 처리방법은 매장으로 방문하시거나 전화해 주시고, 우편이나 택배이용시 배송료는 본인 부담입니다.
- A/S 처리기간은 고장상태와 부품조달 관계로 1주일에서 최장 3개월까지 걸릴 수 있습니다.
상품이 장바구니에 담겼습니다.
바로 확인하시겠습니까?
상품이 찜 리스트에 담겼습니다.
바로 확인하시겠습니까?